Ktl-icon-tai-lieu

AH55 User Manual

Được đăng lên bởi hoangtranelek
Số trang: 8 trang   |   Lượt xem: 304 lần   |   Lượt tải: 0 lần
AH55 User Manual
1. Safety Instruction
1)

All the instruction marked with sign
must be absolutely observed or
executed; otherwise, personal injuries or risk to the machine might occur.

2)

This product should be installed and operated by persons with appropriate
training only.

3)

Before connecting power supply cords to power sources, it’s necessary to make
sure that the power voltage is in the range indicated on the product name plate.

4)

Make sure to move your feet away from the pedals while power on.

5)

Turn off the power and remove plug prior to the following operations:
■

6)

Connecting or disconnecting any connectors on the control box;

■

Repairing or doing any mechanical adjustment;

■

Threading needle or raising the machine arm;

■

Machine is out of work.

Make sure to fasten all the fasteners firmly in the control boxes prior to the
operation of the system.

7)

Allow an interval of at least 30 seconds before repapering the system after power off.

8)

Repairs and maintenance work may be carried out by special trained
electronic technicians.

9)

All the replacement parts for repairing must be provided or approved by the
manufacturer.

10) The controller must be firmly connected to a properly grounded outlet.
Be sure to connect the controller to a properly grounded
CAUTION:

outlet. If the grounding connection is not secured, you
may run a high risk of receiving a serious electric shock,
and the controller may operate abnormally.
Page 1 of 8

2. Installation
(1)Motor Installation
Step 1: Mount lifting bracket. When motor installed under the machine table, as needed,
to drill holes in the following diagrams (see Fig. 2-1 the example for USA base
table) for the installation, mount lifting bracket.

Fig.2-1

Step 2: Install the motor (see Fig.2-2) and then tighten the lifting bracket.

Fig.2-2

(2)Controller Installation

Fig.2-3

Page 2 of 8

3. Power Connection and Grounding
Ground wire (Green/yellow) must be grounded. Use the correct connector and
extension wire when connecting ground wire to Earth and secure it tightly (see Fig.3-4).

Control Box cable

Brown(AC220V)
Blue
(neutral wire)
Y ellow/Green

(Ground wire)

Brown(AC220V)
Yellow/Green
(Ground wire )
Blue(neutral wire)
Control Box

Control Box cable plug

Fig. 3-4

Ensure all power cord, signal wire and grounding wire not be
pressed by other matter or over-twisted ,and not be too close
CAUTION

to belt and belt wheel, keep 3cm-distance for safety.

A 1Ф/220V power from a 3Ф/3...
Page 1 of 8
AH55 User Manual
1. Safety Instruction
1) All the instruction marked with sign must be absolutely observed or
executed; otherwise, personal injuries or risk to the machine might occur.
2) This product should be installed and operated by persons with appropriate
training only.
3) Before connecting power supply cords to power sources, it’s necessary to make
sure that the power voltage is in the range indicated on the product name plate.
4) Make sure to move your feet away from the pedals while power on.
5)
Turn off the power and remove plug prior to the following operations:
Connecting or disconnecting any connectors on the control box
Repairing or doing any mechanical adjustment
Threading needle or raising the machine arm
Machine is out of work.
6) Make sure to fasten all the fasteners firmly in the control boxes prior to the
operation of the system.
7) Allow an interval of at least 30 seconds before repapering the system after power off.
8) Repairs and maintenance work may be carried out by special trained
electronic technicians.
9) All the replacement parts for repairing must be provided or approved by the
manufacturer.
10) The controller must be firmly connected to a properly grounded outlet.
CAUTION
Be sure to connect the controller to a properly grounded
outlet. If the grounding connection is not secured, you
may run a high risk of receiving a serious electric shock,
and the controller may operate abnormally.
AH55 User Manual - Trang 2
Để xem tài liệu đầy đủ. Xin vui lòng
AH55 User Manual - Người đăng: hoangtranelek
5 Tài liệu rất hay! Được đăng lên bởi - 1 giờ trước Đúng là cái mình đang tìm. Rất hay và bổ ích. Cảm ơn bạn!
8 Vietnamese
AH55 User Manual 9 10 998