Ktl-icon-tai-lieu

Gioi thieu ve Delcam

Được đăng lên bởi khanhngoc
Số trang: 404 trang   |   Lượt xem: 6220 lần   |   Lượt tải: 4 lần
Important Notice
This document is supplied as part of a Delcam Training Course. It is not intended to be
distance learning material: rather as an aid for Tutors when presenting material to course
delegates and as a subsequent aid memoir to those delegates.
Delcam does not accept responsibility for any personal belongings / valuables whilst on the
premises. Delegates are advised to keep their belongings on their person at all times.
Delcam plc. has no control over the use of the software described in this document and cannot
accept any responsibility for any loss or damage howsoever caused as a result of using the
software. Users are advised that all results from the software are checked by a competent
person in accordance with good quality control procedures.
The software described in this document is furnished under a license agreement and may be
used only in accordance with the terms of such license.
Copyright  2009 – Delcam plc. All rights reserved

Training Centre
Tel: 0121 683 1050
Fax 0121 7665511

Customer Support
Tel: 0121 683 1010
Fax: 0121 7665542

Contents

PowerMILL

PowerMILL 10 Contents
Chapters

Page Number
PRO
ONLY

Day 1

Day 1-2

Day 3-4

Day 4-5

Day 5

1. Getting Started

1.1 - 1.24

N/A

2. Machining Set Up in Detail

2.1 - 2.16

N/A

3. Area Clearance Strategies

3.1 - 3.26

> 3.38

4. Finish Machining Strategies

4.1 - 4.32

> 4.64

5. Leads and Links

5.1 - 5.12

N/A

6. Boundaries

6.1 - 6.22

N/A

7. Levels and Sets

7.1 - 7.10

N/A

8. Editing Toolpaths

8.1 - 8.22

N/A

9. 2D (Feature Set) Machining

9.1 - 9.23

> 9.30

10. Collision Checking

10.1 - 10.6

> 10.12

11. Patterns

11.1 - 11.14 > 11.22

12. Wireframe Modeller
13. NC Programs

12.1 - 12.22
13.1 - 13.10

N/A
N/A

14. Setup Sheets

14.1 - 14.6

N/A

15. Tool Database

15.1 - 15.20

N/A

16. Customising PowerMILL

16.1 - 16.18

N/A

17. Specialist Finishing (PRO)
18. Component Thickness (PRO)

17.1 --------- > 17.30
18.1 --------- > 18.10

19. Stock Models (PRO)

19.1 --------- > 19.10

20. Additional Information (PRO)

20.1 --------- > 20.2

Issue PMILL 10

1

Contents

2

PowerMILL

Issue PMILL 10

1. Getting Started

PowerMILL 10

1. Getting Started
Introduction.
This course covers the 3-Axis functionality available in PowerMILL. The additional features
available with PowerMILL–Pro and Five Axis licenses are covered in separate modules.
PowerMILL will quickly create gouge free cutter paths on imported component data. It
supports Wireframe, Triangle, Surface, an...
Để xem tài liệu đầy đủ. Xin vui lòng
Gioi thieu ve Delcam - Người đăng: khanhngoc
5 Tài liệu rất hay! Được đăng lên bởi - 1 giờ trước Đúng là cái mình đang tìm. Rất hay và bổ ích. Cảm ơn bạn!
404 Vietnamese
Gioi thieu ve Delcam 9 10 326