Ktl-icon-tai-lieu

ME-430 Introduction to Computer Aided Design - HAMMER HANDLE - Pro/ENGINEER Wildfire 2.0

Được đăng lên bởi Anhvu Lê
Số trang: 23 trang   |   Lượt xem: 2602 lần   |   Lượt tải: 0 lần
ME-430 Introduction to Computer Aided Design

HAMMER HANDLE - Pro/ENGINEER Wildfire 2.0
Dr. Herli Surjanhata

In a system window, create a new directory called ME-430 (e.g.
h:\PTC_Working_Dir\ME-430) if this has NOT been done.
From File pull down menu, select Set
Working Directory.
Select Working Directory dialog
box appears

1

Select the ME-430 directory
to highlight it and select OK.
All files created in this
session will be stored in ME430 directory.
Note:

You can also create a new
directory by selecting

Pick the Create a new object icon

.

.

2

Type in hammer_handle for the name
of the new part.
Click OK.

CREATE A BASE FEATURE – REVOLVED PROTRUSION
Create the base feature – Pick the
.

Revolve Tool icon

In the dashboard,
pick

, then

click

.

3

Pick Front datum plane as Sketch Plane.
For Sketch Orientation Reference pick
RIGHT datum plane, and set Orientation to
Right. This option is default option!
Then click the Sketch button

.

Click the Close button in the
References dialog box.

4

Click the small forward > icon to expand,

.

and pick

Draw a horizontal centerline through
coordinate system. This centerline is
used as axis of revolution of the revolved
section.
Use the appropriate Sketcher Tools to create and dimension the section as shown
below – make sure the section is closed, and use diametrical dimensions for the
cylindrical portion of the hammer (see figure below).

,

,

,

,

,

Click

Click

.

.

5

and select Standard
Click
Orientation.

CREATE CHAMFERS

Pick the Chamfer Tool icon

.

Pick the right edge of the handle.

Change the chamfer option to 45 x D.
Enter the D value of 0.1795 in.

6

Click

to finish creating a chamfer.

Repeat the same technique to create two more chamfers as shown below.
Chamfer 45° x 0.1795

Chamfer 45° x 0.035

CREATE A GROOVE
Create the base feature – Pick the
Revolve Tool icon

.

7

In the dashboard,
click the Remove
.

Material icon

Then pick
,
followed by clicking
.

Pick Front datum plane as Sketch Plane.
For Sketch Orientation Reference pick RIGHT
datum plane, and set Orientation to Right. This
option is default option!
Then click the Sketch button

.

Pick as additional
reference.

Pick as additional
reference.
Pick the top horizontal and vertical left edges as the
reference.
Click the Close button in the References dialog box.

8

The groove will be created using revolved cut. Create the following section, make
sure to create the horizontal centerline first, next draw the vertica...
1
ME-430 Introduction to Computer Aided Design
HAMMER HANDLE - Pro/ENGINEER Wildfire 2.0
Dr. Herli Surjanhata
In a system window, create a new directory called ME-430 (e.g.
h:\PTC_Working_Dir\ME-430) if this has NOT been done.
From File pull down menu, select Set
Working Directory.
Select Working Directory dialog
box appears
ME-430 Introduction to Computer Aided Design - HAMMER HANDLE - Pro/ENGINEER Wildfire 2.0 - Trang 2
Để xem tài liệu đầy đủ. Xin vui lòng
ME-430 Introduction to Computer Aided Design - HAMMER HANDLE - Pro/ENGINEER Wildfire 2.0 - Người đăng: Anhvu Lê
5 Tài liệu rất hay! Được đăng lên bởi - 1 giờ trước Đúng là cái mình đang tìm. Rất hay và bổ ích. Cảm ơn bạn!
23 Vietnamese
ME-430 Introduction to Computer Aided Design - HAMMER HANDLE - Pro/ENGINEER Wildfire 2.0 9 10 678